A 5x120 wheel has five bolt holes on a 120mm pitch circle. It will not bolt directly onto a 5x112 hub. Before buying, confirm your car’s stud pattern, then check the centre bore and offset. The wheel must also clear the brakes and suit the tyre size you plan to run.
For a BMW or Commodore build, the badge alone does not confirm fitment. Check the specification for your car before choosing a wheel.
Why a 5x112 wheel will never bolt onto a 5x120 hub
The pitch circle diameter, or PCD, is the diameter of the circle passing through the centre of each stud or bolt hole. Both patterns have five holes, but their circle diameters differ by 8mm. The holes will not line up.
If your measurement falls between two patterns, measure again before ordering. Use calipers and the correct method for a five-stud pattern, not a photo. A 5x100 wheel is another distinct pattern, not a substitute. Our mag wheel fitment guide on this blog covers the measuring steps.
Which cars in NZ usually run 5x120 and which run 5x112
Many BMWs and Holden Commodores use 5x120. Many VW and Audi models use 5x112. Those are starting points, not fitment confirmation: specifications can change between model years and trims.
Confirm the pattern for your particular vehicle from reliable specifications. If you cannot confirm it, ask before buying.
Check the centre bore and hub-centric ring
The centre bore is the hole that fits over the hub spigot, the raised collar on the hub. Some aftermarket wheels have a larger bore so they can suit different vehicles. A hub-centric ring fills the gap where the wheel’s fitment requires one.
The ring helps locate the wheel centrally during fitting. It is not a substitute for correct wheel fasteners or tightening. Choose it by both measurements: the wheel’s bore diameter and the hub’s outside diameter, not just the size of the gap.
Check that the ring seats fully and the wheel sits flush against its mounting surface. A ring cannot correct the wrong PCD, and it cannot make a wheel with too small a bore fit.
How offset moves the wheel inside the guard
Offset, usually marked ET, is the distance in millimetres between the wheel’s mounting face and its centreline. For wheels of the same width, a higher positive offset places the wheel further inboard. A lower offset moves it outward.
A few millimetres can decide whether a tyre rubs, so do not compare offset on its own. Look at the width beside it, because a wider rim changes where the tyre sits in the guard.
Offset and backspacing are different numbers
Backspacing measures from the mounting face to the inner edge of the rim. It describes how far the wheel extends inward. Two wheels with the same offset but different widths have different backspacing, so check which measurement a listing gives.
Why offset alone does not prove clearance
A wheel can have a suitable offset and still hit a brake caliper. Spoke shape and inner barrel clearance matter, particularly with concave designs or larger brakes.
Check the manufacturer’s clearance information and test-fit where possible. Check the guards too, allowing for steering movement and suspension travel. Our mag wheel fitment guide on this blog covers clearance checks in more detail.
Match the lug seat to the wheel
Conical nuts have a tapered seat. Ball-seat nuts have a rounded seat, while flat washer types bear against a flat face. These designs are not interchangeable: the wrong seat can prevent the fastener from clamping the wheel correctly.
Match the seat to the wheel, then confirm the fastener’s thread and required engagement for the vehicle. A hub-centric ring does not correct an unsuitable nut or bolt.
What a wheel spacer changes and what it adds
A spacer moves the wheel outward and reduces its effective offset. That changes clearance and the leverage applied to the hub assembly. A spacer may create room behind the wheel while causing a tyre to rub against the guard.
Do not choose one just to make an unsuitable wheel fit. Spacer design and fastening requirements need checking for the vehicle, along with any certification requirements. Longer studs alone do not establish that an arrangement is suitable.
Will wider wheels pass a WoF in New Zealand
Width alone does not decide. Changes to track width or tyre coverage can affect WoF compliance, and some modifications require low volume vehicle (LVV) certification. Check the current NZTA requirements for the proposed change before ordering parts.
A wheel that looks flush is not proof of compliance. Ask a certifier about LVV requirements before you order, since the answer depends on the exact change.
Bring your fitment details to Mag & Turbo Waiwhakaiho, New Plymouth
Bring your rego and full vehicle details, including the trim or engine variant. If you have chosen wheels, bring their PCD, bore and offset specifications, plus the intended tyre size. Mark anything you do not know rather than guessing.
Call 06 777 1700 or visit Mag & Turbo Waiwhakaiho, New Plymouth at 2/674 Devon Road. You can browse our wheels collection or send your vehicle details through the contact form before buying. Tyres bought from Mag & Turbo Waiwhakaiho, New Plymouth get free puncture repairs and rotations for life. Through Mag & Turbo Country Wide Support, that care is also available at Mag & Turbo stores around New Zealand.
Warning signs after the wheels go on
New vibration or rubbing after a wheel change needs checking. Do not assume it will settle as you drive.
Signs that mean stop and get it checked
Stop driving if the tyre is making contact.
Other warning signs include:
- Vibration at speed that started after the wheel change.
- Rubbing when turning or travelling over bumps.
- Visible marks where the tyre or wheel has touched the guard or suspension.
Taranaki’s coastal salt can contribute to corrosion on hubs and wheel fasteners. Clean the mating surfaces before fitting, use the specified tightening torque and follow the wheel or vehicle manufacturer’s instructions for rechecking fasteners.
Shortcuts that have no place on a road car
Do not use wobble bolts or redrill a hub as a DIY fix for the wrong PCD. A ring changes how the centre bore locates; it does not change the bolt pattern. The starting point remains a wheel specified for your car.
If a wheel change has left you with vibration or rubbing, book a workshop appointment online to have it checked. If the tyre is touching or you suspect loose fasteners, stop driving rather than driving to the appointment.
Frequently asked questions
Will 5x112 wheels fit a 5x120 car?
No, they will not bolt directly onto the hub. The pitch circle diameters differ by 8mm, so the holes do not line up. Choose the exact PCD specified for your vehicle.
What cars in NZ use 5x120 wheels?
Many BMWs and Holden Commodores use 5x120. The pattern varies by model and year, so confirm your car’s specification rather than buying by badge alone.
Is 5x100 the same as 5x112?
No. Both have five holes, but one has a 100mm pitch circle and the other has a 112mm pitch circle. They are not interchangeable.
What is the difference between conical and ball seat lug nuts?
Conical nuts have a tapered seating surface; ball-seat nuts have a rounded one. The seat must match the wheel so the fastener clamps correctly. Confirm the thread and required engagement for your vehicle as well.
Talk to us
Not sure what fits? Ask Mag & Turbo Waiwhakaiho, New Plymouth. We check fitment and fit your wheels in our New Plymouth workshop. You can browse wheels at hookmeup.co.nz, check your tyre size, or book online.