In New Zealand, the minimum tyre tread depth is 1.5mm in the principal grooves around the whole tyre, or 4mm for winter tyres. Those are WoF limits, not wet-grip targets. For wet-road driving, plan to replace your front tyres at about 3mm rather than waiting until they barely pass.
Check every tyre, not just the fronts. A deep centre groove can hide a worn shoulder, and enough tread does not cancel out sidewall damage.
What is the legal minimum tread depth for a WoF in NZ?
The NZTA Vehicle Inspection Requirements Manual requires at least 1.5mm in the principal grooves around the whole circumference. Winter tyres need at least 4mm. A reading below the relevant minimum fails the tread-depth requirement.
At 1.5mm, a standard tyre has no tread-depth margin left before it becomes illegal. Plan replacement before that point, particularly if your vehicle spends much of its time on wet roads.
How do WoF inspectors measure tread across the tyre?
The inspector checks the principal grooves that normally contain moulded tread wear indicators. The minimum depth must hold all the way around the tyre. Where there are no indicators, the requirement applies across at least three-quarters of the tread width. Tie-bars and indicator strips are excluded from the measurement.
Look beyond the centre groove. A tyre with good tread in the middle can still fail because of wear elsewhere in the measured area.
Check both shoulders, and as much of the circumference as you can safely reach.
Inspectors also check for damage. Under NZTA's rules, a sidewall or tread cut or crack longer than 25mm that reaches the cords is a fail. Exposed cords also fail, as do cut cords. On the same axle, tyres must have matching size designations and carcass construction, with the same tread pattern type.
Where are the tread wear indicator bars, and how do you read them?
Tread wear indicators are raised rubber bars moulded into the principal grooves, commonly about 1.6mm high. Many tyres mark their position on the sidewall with a triangle or the letters TWI. If the tread is level with those bars, arrange replacement rather than trying to use the tiny margin above New Zealand's 1.5mm minimum.
Check more than one bar.
Uneven wear can leave one groove level with its indicator while another still looks deep. Use a gauge for the actual depth, especially if a tyre is close to its limit.
How do you check tread depth at home with a 20c coin or a gauge?
A New Zealand 20c coin gives you a rough check around 2mm. It does not measure the legal limit precisely.
- Choose a principal groove, away from a raised indicator bar.
- Insert the coin with the number 2 facing you and its bottom edge down in the groove.
- Look at the bottom of the 2. If the tread covers it, the depth is above about 2mm. If you can see it, the tread is at or below about 2mm and replacement is recommended.
- Repeat across the tread and at different points around the tyre. Check the shoulders for uneven wear too.
A coin cannot tell you whether you have 3mm left. For that, use a tread-depth gauge: seat its base flat across the groove, extend the probe to the groove floor and read the depth. Measure several places on each tyre, avoiding the raised bars.
Why does wet braking get worse before the tread reaches 1.5mm?
Tread grooves channel water away so the rubber can contact the road. As those grooves become shallower, they have less capacity to clear water. Standing water and higher speeds increase the risk of losing grip.
For regular wet-road driving, about 3mm is a sensible replacement point for front tyres. That is a practical recommendation, not an NZTA requirement or a guarantee of grip. Tyre condition and the amount of water on the road still matter.
A WoF checks minimum roadworthiness requirements; it is not a wet-braking performance test. On your trips around New Plymouth and Taranaki, reduce speed when water is lying on the road and leave more stopping distance. New tyres do not make standing water safe at speed.
What does uneven tread wear tell you about the car?
Check tyre pressures first. Wear across both shoulders often points to under-inflation, while centre wear can point to over-inflation. One worn edge needs an alignment and suspension check.
| Wear pattern | Likely cause | Next step |
|---|---|---|
| Both shoulders worn, centre still has tread | Under-inflation | Check pressures when cold and adjust to your vehicle's placard. Have the remaining tread checked before continuing to use the tyre. |
| Centre worn, shoulders still have tread | Over-inflation | Check cold pressures against the vehicle's recommended figure. |
| One edge worn | Incorrect alignment or worn suspension components | Have the alignment checked and suspension inspected before fitting replacement tyres. |
Replacing a tyre does not fix the fault that wore it out. If alignment or a worn suspension part caused the damage, leaving it unresolved can ruin the replacement too.
What should you do when your tyres reach the replacement point?
Plan front-tyre replacement at about 3mm for wet-road use. Winter tyres need replacement before they drop below 4mm. If wear is uneven, have the cause checked before new tyres go on, and make sure replacements meet your vehicle's load and fitment requirements.
Mag & Turbo Waiwhakaiho, New Plymouth, is at 2/674 Devon Road. Tyres bought from Mag & Turbo Waiwhakaiho, New Plymouth get free puncture repairs and rotations for life. Through Mag & Turbo Country Wide Support, that care is also available at Mag & Turbo stores around New Zealand. We can also help you apply for finance through a lender. To arrange fitting, book into the workshop online, or ask about tyres for your vehicle. For a damaged tyre, see the puncture repair guide.
Frequently asked questions
Can I fail a WoF for uneven tyre wear?
Yes. A standard tyre fails the tread-depth requirement if any part of the required measurement area is below 1.5mm. Inspectors check the principal grooves around the whole circumference, or at least three-quarters of the tread width where there are no indicators, so a good centre reading alone is not enough.
What is the legal tread depth for winter tyres in NZ?
NZTA requires at least 4mm in all principal grooves that normally contain tread wear indicators, around the whole circumference. Do not apply the standard 1.5mm limit to winter tyres. Plan replacement before they fall below 4mm.
Will a WoF pass tell me my tyres stop well in the rain?
No. A WoF pass confirms compliance with inspection requirements, not wet-braking performance. For regular wet-road driving, plan to replace front tyres at about 3mm rather than waiting for the 1.5mm legal minimum.
Can a sidewall cut fail a WoF?
Yes. NZTA rejects a sidewall or tread cut or crack longer than 25mm if it reaches the cords. Exposed cords or cut cords also cause a fail, regardless of how much tread remains.
Do I need a wheel alignment after fitting new tyres?
Have the alignment checked when fitting new tyres, especially if the old tyres wore on one edge or your vehicle pulls to one side. Worn suspension parts may also need attention. Ask for those checks when booking your tyre fitting at Mag & Turbo Waiwhakaiho, New Plymouth.
Talk to us
Talk to Mag & Turbo Waiwhakaiho, New Plymouth about the right tyres for your car. Visit us at 2/674 Devon Road, or book online. You can also shop tyres at hookmeup.co.nz. Every tyre is fitted in our New Plymouth workshop. Tyres bought from us get free puncture repairs and rotations for life. Through Mag & Turbo Country Wide Support, that care is also available at Mag & Turbo stores around New Zealand.